Relay 5V 1 Channel for Arduino Active Low In 5V Out 250VAC 30VDC 10A

 

Relay 5V 1 Channel for Arduino Active Low In 5V Out 250VAC 30VDC 10A - This is a 5V 1-Channel Relay interface board. Can be used to control various electrical devices with large currents. Controlled directly by the microcontroller of your choice (Arduino, 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL logic.
Specification:
5V 1-Channel Relay interface board, sink current 15 mA - can be directly from the microcontroller pins;
Relay capacity, AC250V 10A ; DC30V 10A;
The standard TTL logic interface is directly controlled by the microcontroller (Arduino, 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL logic)
Protection circuit (kickback current) is included - safe and ready to use
LED indicator to indicate the active channel
Active LOW - check https://streamable.com/3e16i
Buyer gets 1 1 channel relay module.

Pure Sine Inverter Driver Board Module EGS002 EG8010 IR2110 IR2113 pc

Pure Sine Inverter Driver Board Module EGS002 EG8010 IR2110 IR2113 pc - NEW EGS002 Pure sine wave inverter driver board EG8010 + EG2113 / IR2113 / GNVS2113 module, (NOT 2110, there are many 2110 / cheaper in the market)

EGS002 is a Sine Wave Generator Driver module to create a Sine Wave Inverter by adding Mosfet/IGBT.

Old:

EG2110 / IR2110 V-offset 500v

New:

EG2113 / IR2113 V-offset 600v

Pure Sine Wave 2000W 3000W 4000W Power Inverter Kit 12/24/36V to 220V

 

Pure Sine Wave 2000W 3000W 4000W Power Inverter Kit 12/24/36V to 220V - 

Power Inverter Kit Pure Sine Wave 600 - 1500 Watt + 180A Iron Core Ankle Transformer.
This Assembled Power Inverter Kit has 1 set with an Iron Core Ankle Transformer Pure Copper wire to be able to work to produce Pure Sine Wave electricity 
the same as Electric Waves from PLN so it is safe for all Electronic, Resistive and Inductive Equipment such as water pumps, washing machines , Fan, Blender, 
Electric drill, Refrigerator, Air conditioner, and more.
Description :
Input : 36V DC
Output : 220V AC +/-5%
Frequency : 50 Hz
Output Wave: Pure Sine Wave (Pure Sine Wave)
Static/No Load Power : 0.2A
NOTES:
36V battery VOLT, maximum power 1500W
This Inverter Kit need to connect to the transformer.
-36V battery, Use about 21V transformer (21V to 220V)
The suitable transformer for this Inverter kit is Zero / Ankle Transformer EGS002.
If there is damage, spare parts from this Pure Sine Power Inverter Kit are often found in Electronic Stores and can be repaired or contact us again for repair.

Electret microphone preamplifier module adjustable gain

 

Electret microphone preamplifier module adjustable gain - Cheer for your project. The fully assembled and tested circuit board has a soldered 20-20KHz electret microphone. 
The amplifier has excellent power supply noise suppression, so the amplifier does sound good.
This breakthrough is most suitable for projects that use FFT, such as voice converters, audio recording sampling, and audio responsive projects. 
We include a small trimmer potentiometer to adjust the gain. You can set the gain from 25 times to 125 times. Down to about 200mVpp (normally, about 6 inches away), 
ideal for connecting to something that requires "line level" input without clipping, or up to about 1Vpp, ideal for reading from microcontroller ADCs. 
The output is rail-to-rail, so if the sound is loud, the output can be up to 5Vpp
-Ground GND, VCC to 2.4-5VDC.
-For best performance, use the "quietest" power supply available (on Arduino, this will be a 3.3V power supply).
-Audio waveforms will be output from the OUT pin. The DC bias of the output is VCC/2, so when its
-Completely quiet, the voltage will stabilize to VCC / 2 volts (DC coupled). If you use audio equipment
-AC coupled audio is required, please place a 100uF capacitor between the output pin and input of the device. in case
-You want to connect to an audio amplifier with differential input or including decoupling capacitors,
-No upper limit of 100uF is required.
-The output pin is not used to drive speakers or anything, but the smallest in-ear headphones-you need
-If you want to connect the amplifier directly to the speakers, please use an audio amplifier (eg 3.7W stereo amplifier). What if you are
-Connect to microcontroller pin, no amplifier or decoupling capacitor required-Connect to OUT
-Connect directly to the ADC pin of the microcontroller.
-For projects with audio responsiveness, we recommend using the FFT driver library, which can take audio input and "convert" it to
-frequency.
The fixed gain is 20dB, which can support two power supply modes of 3.3v and 5v.

Z-80 Microprocessor Trainer (Microprocessor Training Kit)

 

Z-80 Microprocessor Trainer (Microprocessor Training Kit) - This product is a Z-80 microprocessor practicum tool equipped with an 8-bit LED output. 
Very suitable for students and students, and hobbyists
Always ask for stock conditions before ordering.
Specification:
CPU: Z80-CPU
RAM: 2 Kbyte and expandable up to 4 Kbyte (6116)
EPROM: 2 Kbyte
Display: 6 digit seven segment
Keyboard: 36 keys (19 function keys, 16 hexa digit keys and 1 reset key)
Krisbow aluminum suitcase packaging
Package contains:
Z80 Microprocessor Trainer
PIO LED Output Interface
AC to DC Power Supply 5V / 500mA
Practice guide and answer key (PDF file)