PLC Programmable Controllers Allen Bradley Rockwell Automation

PLC Programmable Controllers  -  Allen‑Bradley® programmable logic controller (PLC) and programmable automation controller (PAC) range from large to small and even micro applications. We offer different controller types and sizes to fit your specific needs.

Allen Bradley 1756-L62 ControlLogix Logix5562 Processor with 4 Mbyte Memory. Available User Memory: 4096 Kbytes; I/O Memory: 478 Kbytes; 

Nonvolatile Memory: 64 Mbytes CompactFlash (1784-CF64). The 1756-L62 controller can be inserted into any slot of a chassis, 

multiple controllers can be installed in the same chassis. Multiple controllers in the same chassis communicate with each other across the backplane 

but operate independently. The 1756-L62 Controllers can communicate across RS-232-C (DF1/DH-485 protocol), DeviceNet, DH+, ControlNet & EtherNet/IP networks. 

To provide communication for a ControlLogix controller, an appropriate communication interface module must be installed in the chassis

Best Super Carrier Board - Basic Stamp Parallax Inc

Basic Stamp Super Carrier Board - Low-cost through-hole development board for the BASIC Stamp 1 (BS1-IC) and the 24-pin BASIC Stamp 2 series microcontrollers (BS2-IC, BS2E-IC, BS2SX-IC, BS2P24,BS2PE, and BS2PX24), and Javelin Stamp modules. This board is often used for experiments and permanent BASIC Stamp projects soldered to the through-hole area.  A number of protective enclosures are also available to finalize your project.Practical modules for the BASIC Stamp BS1-IC and BASIC Stamp 2 Series. Suitable for prototyping projects based on BASIC Stamp

Features:

9 VDC power supply (battery connector or DC Jack)
Features Supports BS1 with 14-pin and 24-pin DIP packaging, supports BASIC Stamp 2 with 24-pin DIP packaging, solder-hole area available
Microcontroller/microprocessor based -
Number of I/O ports 16
DB9 . Serial interface port
Bootloaders -
DB9 programming port (Basic Stamp 2) and 3-pin Header (BASIC Stamp 1)
Datasheet : http://www.parallax.com/Portals/0/Downloads/docs/prod/schem/supercarrierbd.pdf

All FM AM (MW SW) SSB (LSB USB) Band Radio Receiver Speaker

All FM AM (MW SW) SSB (LSB USB) Band Radio Receiver Speaker - SI4732 All Band FM Radio Receiver AM (MW SW) SSB (LSB USB) supports Speaker with antenna + USB cable
Information:
Use 3.6V . lithium battery
USB charging
Support 3.5mm . audio and headset output
Supports 8 ohm 1W speaker speakers
FM output supports headphone antenna
Using the BNC antenna interface
The PCB retains the si4735 package, users can change the chip by themselves, and the software is compatible.
Feature:
FM, am (MW and SW) and SSB (LSB and USB);
Audio bandwidth filters 0.5, 1, 1.2, 2.2, 3 and 4kHz
22 pre configured commercial radios and amateur bands
BFO Control
Step frequency switch (1, 5 and 10kHz)
Frequency band
Type Fm_band_, 8400,10800,10430,10,
Type Lw_band_,100,510,300,1,{Mw_band_type
520,1720,810,10,
Sw _ band _ type, , 1}, / / ​​160m
Sw _ band _ type, , 1}, // 80m
Type Sw_band_,
4500,5500,4850,5}
Sw _ band _ type, 5500,6300,6000,5 },{Sw _ band _ type,
, 5}, // 40m {SW}_ band _ type, 7800,10000,9600,5}
Sw _ band _ type, 00, 1}, /30m
Type Sw_band_, 11000,12500,11940, 5},
Sw _ band _ type, 12500,13900,13600,5 },{Sw _ band _ type,
13900, 14500, 14270, 1}, /20m
Type Sw_band_, 14500.15900.15300.5}
Type Sw_band_, 15900.17900, 17600,5}
Type Sw_band_, 17900,18300,? 18100, 1}, /17m
Type Sw_band_, 18300,? , 1}, /15m
Sw _ band _ type, 40, 1}, / / ​​12m
Sw_band_Type, 00, 1}, // CB band (11m)
sw _ band _ type, 27900,30000,28400,1} //; // 10 meters
Notes:
Due to the different monitor and light effect, the actual color of the item may be slightly different from the color shown on the pictures. Thank you!
Please allow 1-2cm measurement deviation due to manual measurement.
Support 3.5mm . audio and headset output
Supports 8 ohm 1W speaker speakers
FM output supports headphone antenna
Using the BNC antenna interface

Best PIC Microcontrollers In Sytem Programming

PIC In System Programming - PIC microcontrollers, like most modern microcontrollers, can be programmed in system (or in circuit – ICSP) rather than in a socket programmer. 

This has advantages in development and in production, for example, to use different firmware for different versions or to speed up production. 

The major benefit though is field upgrades.PIC microcontrollers are a very useful and versatile tool for use in many electronic projects. They are very inexpensive and easy to find. They are also very powerful and many are capable of speeds up to 64 MIPS using the internal oscillator block, about 16 times faster than most comparable AVR microcontrollers. 
PICs are also easy to program, however getting the project set up can some times be tricky. These instructions will walk through the process of setting up the 
software, creating a new project, and programming some very simple functions to test the configuration and ensure everything is working. They are designed to be 
very open ended; after the project is created and the basics are finished the reader is encouraged to explore all the features and extras not covered in these 
instructions. Also you will find that these instructions will start out walking through step by step, but as the instructions near the end the reader is 
encouraged to explore other ways of accomplishing the tasks and make the project their own.

1. Programmer PIC K150

Support the most popular programming PIC chips, read, encryption and other features.

No external power supply,communication and power is only a USB cable to print complete, without any cable.

PICSTARTPLUS much faster rate than programming.

Can easily read the contents of the chip program area.

Automatic programming verification.

Comprehensive information prompts, allowing users to understand the working state.

With 40pin ZIF programming of the seat, can be directly programmed in 8-pin to 40 pin PIC microcontroller chip 

can be programmed using ICSP online or add conversion blocks.

8 pin 40 pin-board outside the chip can be downloaded directly online ICSP output.

Compatible with Windows98 and Windows2000/NT, Windows XP / Windows 7 and other operating systems.

Specifications:

Original box: No

Color board: blue

Item size: 90*46*10mm

Net weight: 103g

Package weight: 112g

Package included:

1 x Programmer

1 x High quality USB cable

1 x ICSP cable

2. PX-200 OEM-PICkit2 USB Flash PIC ISP In-System Programmer

PX-200 OEM-PICkit2 USB Flash PIC In-System Programmer . ICSP device (programmer) for PIC microcontroller.

Specification:

- Supports PICs:

PIC10Fxx, PIC12F5xx, PIC16F50x/5x, PIC12F615/ HV615, PIC16F7x/ 7xx, PIC12F62x/63x/67x/68x, PIC16F84x/8xA/8xx/8xxA, PIC16F6xx, PIC16F9xx, PIC18x, 

PIC18xx, PIC18x PIC18F8xxx, PIC18F9xJ6x, PIC18F4xxx, PIC18F2xJxx/4xJxx, PIC24FJ6xGA0xx, PIC24FJ9xGA0xx, PIC24FJ128GA0xx

- Interface: USB

- Does not require additional power supply.

- There are 3 LED indicators for Power, Target, Busy

- Compatible with Windows operating system (98, ME, XP)

3. USB ICSP PIC Programmer

Usb pic programmer is designed to program popular Flash PIC Microcontroller which includes most of the PIC family. Besides 8-bit, it can also program 16-bit and 

32-bit PIC MCU. On board ICSP (In Circuit Serial Programming) connector offers flexible methods to load program. USB port is commonly available and widely used 

on Laptop and Desktop PC, thus is very convenient to use UIC00B. It offers reliable, high speed programming and free windows interface software

ARM Cortex M0 Microcontroller Learning Module Nu LB Nano130 32Bit

ARM Cortex-M : Modular Embedded Systems Design (FREE!) - Learning board for Nano130 microcontroller. This microcontroller is a 32-bit microcontroller that has been integrated with ARM Cortex-M0 with low power consumption.

The Nu-LB-Nano130 board can be used for learning media using the Nano130 microcontroller by displaying information via the LCD, data storage or serial 
communication to a PC.
Specifications:
- Power supply: 5VDC
- Has a series of I / O for LCD panels, 7 Segments, LEDs, RGB LEDs, Potentiometers, Switches, EEPROM, Flash Data, etc.
- Already integrated with Nu-Link-Me so no need for an external programmer/debugger.
- ISP programming (via bootloader) can only be used via Serial port (DB-9).
- Can be programmed using the C programming language and using IAR, Keil, or CooCox CoIDE compilers.
- Get the latest information and exchange opinions on the use of this product through the Nuvoton-M0 forum.
Datasheets:
http://download.nuvoton.com/NuvotonMOSS/DownloadService/Member/DocumentsInfo.aspx?tp_GUID=UG0220121210173033